Free checklist
Concrete repair and restorationConcrete repair and restoration final inspection checklist
Concrete repair and restoration final inspection is where the punch list is either short or expensive. This checklist walks the finished work the way an owner or AHJ will see it: devices on, systems running, everything labeled. Each item gets the photo that closes it instead of reopening it. Work is commonly verified against ICRI guidance, ACI, manufacturer's published instructions. Confirm the edition your authority having jurisdiction has adopted.
- Items
- 4
- Photos required
- 7
- Built for
- General contractors
Who runs it
The GC's superintendent with the restoration foreman, walking completed repairs after cure.
When in the schedule
After the repair mortar has cured and any curing protection comes off, before the surface is coated, sealed or handed over.
The checklist
Every item, and the photo that proves it
The photo count on each row is what RTI would require before the item can be submitted. Copy the list as is, or load it into RTI and let the gate enforce it.
Placement and bond
- 2 photos
Mortar consolidated and bonded with no voids
Repair worked tight into the cavity and around reinforcement, no honeycomb or edge voids, full contact against the prepared substrate.
- 2 photos
No drummy areas on sounding
Cured repair sounded across its face and at the edges, ringing solid with no hollow or drummy response indicating debonding.
Finish and profile
- 2 photos
Profile and finish match the surrounding surface
Repair struck to the surrounding plane, texture and finish blended so the patch reads with the adjacent concrete, edges clean.
Cure and protection
- 1 photo
Repair cured and protected as specified
Curing method applied and held for the required time, protection in place against sun, wind or traffic, no premature shrinkage cracking at the perimeter.
What usually sends this back
The failures are almost always the evidence, not the work
- Patch faces struck flush but the finish and texture never blended, so every repair reads as a bright rectangle against the surrounding concrete.
- Repair placed and troweled but never sounded after cure, so a debonded area is discovered later when a coating blisters over it.
- Curing cut short because the schedule needed the area, leaving shrinkage cracking around the perimeter of the patch.
Run it with the Photo Gate
A checklist nobody can submit half-finished
Load this list into RTI, stick a QR tag on the area it covers, and the submit button stays locked until every mandatory item is answered and the 7 required photos exist. Approved walks roll into a branded turnover package with a tamper-evident record behind every line.
Submission state
The gate is enforced on the server, so it holds even if the phone is offline when the walk happens.
Verified against
Common questions
- What does this concrete repair and restoration final checklist cover?
- 4 items across 3 sections, covering placement and bond, finish and profile, cure and protection. Each item spells out what the person walking the job is actually looking for, not just a box to tick.
- Who should run this inspection?
- The GC's superintendent with the restoration foreman, walking completed repairs after cure.
- When in the schedule should this walk happen?
- After the repair mortar has cured and any curing protection comes off, before the surface is coated, sealed or handed over.
- Why does every item ask for a photo?
- 7 of the 4 items call for photo evidence. A checklist answer without the photo is a claim; the photo is what makes the record worth something in a dispute and lets a reviewer approve work without re-walking the job.
- What most often fails a concrete repair and restoration final inspection?
- Patch faces struck flush but the finish and texture never blended, so every repair reads as a bright rectangle against the surrounding concrete. Repair placed and troweled but never sounded after cure, so a debonded area is discovered later when a coating blisters over it. Curing cut short because the schedule needed the area, leaving shrinkage cracking around the perimeter of the patch.
- Can I use this checklist in RTI?
- Yes. Start a free RTI workspace, build this list as a checklist, and the Photo Gate holds the submit button until every mandatory item is answered and its photos are attached. Approved inspections roll into a branded turnover package with a tamper-evident audit trail.
Related checklists
2642 items and 4211 photo requirements in total.