What does this frp wall panels final checklist cover?

13 items across 4 sections, covering bond and flatness, trims and joints sealed, penetrations, condition and handover. Each item spells out what the person walking the job is actually looking for, not just a box to tick.

Who should run this inspection?

The panel installer with the GC's superintendent, walking the finished walls before the space is put into service.

When in the schedule should this walk happen?

After panels, trims and sealant are complete, before the kitchen or wet area is put into service and cleaned down.

Why do these items ask for a photo?

10 of the 13 items call for photo evidence, 12 photos in all. A checklist answer without the photo is a claim; the photo is what makes the record worth something in a dispute and lets a reviewer approve work without re-walking the job.

What most often fails a frp wall panels final inspection?

Adhesive coverage short of full contact, so panels bubble and lifting starts at the corners the first time the wall is washed down. Division bars and trims dry-set with no sealant, so wash water runs behind the panels at every joint. Cutouts around outlets and pipes left oversized and open, so the sealant can not bridge them and the seam stays wet.

Can I use this checklist in RTI?

Yes. Start a free RTI workspace, build this list as a checklist, and the Photo Gate holds the submit button until every mandatory item is answered and its photos are attached. Approved inspections roll into a branded turnover package with a tamper evident audit trail.

Free checklist

FRP wall panels

FRP wall panels final inspection checklist

FRP wall panels final inspection is where the punch list is either short or expensive. This checklist walks the finished work the way an owner or AHJ will see it: devices on, systems running, everything labeled. Each item gets the photo that closes it instead of reopening it. Work is commonly verified against the applicable building code, manufacturer's published instructions. Confirm the edition your authority having jurisdiction has adopted.

Start free with this checklist Download as PDF

The checklist

Every item, and the photo evidence it needs

The photo count on each row is what RTI would require before the item can be submitted. Work the list here and watch the gate hold, or load it into RTI and let it enforce the real thing.

Bond and flatness

Panels fully bonded and flat
Full adhesive contact with no bubbles or lifting, panels flat and tight to the wall, seams aligned and even across the run.
Panel fastening matches the manufacturer's method
Fasteners, where the method uses them, at the listed spacing in oversize holes and snug without dimpling or cracking the face; no stray holes on adhesive-only walls.
Texture face out and color consistent on every sheet
Pebbled face out on every panel, same color and lot across the wall, no sheet hung with its smooth back showing.
Adhesive squeeze-out and layout marks cleaned off the face
No adhesive at seams or molding edges, pencil lines or shipping residue left on the panel face or in the texture.

Trims and joints sealed

Division bars, trims and top edge sealed
Trims and division bars set with continuous sealant, top and bottom edges sealed, joints closed so wash water can not get behind the panels.
Expansion gap held inside the moldings at base, ceiling and corners
Panel edges stop short inside the moldings by the gap the manufacturer lists, not jammed tight at corners, ceiling or floor, with the trim covering the gap.
Corner moldings seated full height on both legs
Inside and outside corner moldings run full height, both legs tight to the panels, ends cut square where they meet the cap and base.
Raw panel edges capped at door frames, base and ceiling
Edge or cap molding at every termination, with no raw cut edge left where wash water, mops or carts reach it.
Washdown joint sealant matches the spec and the panel system
Where the spec requires sealed joints for washdown, the sealant in moldings and at the base is the type the spec and panel manufacturer list, tooled with no voids.
No photo

Penetrations

Cutouts clean and sealed at outlets and pipes
Cutouts tight and centered, plates and escutcheons covering the edge, sealant closing the gap at every penetration.

Condition and handover

Panel faces free of install damage before handover
No cracks, crazing, chips or scuffs from lifts, ladders or trim tools on the finished face; damaged sheets noted by wall for replacement.
Adhesive cure time before washdown given to the super
Time the adhesive manufacturer lists before wet cleaning or mounting wall-hung equipment given to the super and posted at the room.
No photo
FRP cleaning methods and cleaners to avoid handed to the owner
Owner has the panel manufacturer's cleaning methods, including the cleaners, pads and pressure washing limits that damage the surface or trims.
No photo

What usually sends this back

The failures are almost always the evidence, not the work

Adhesive coverage short of full contact, so panels bubble and lifting starts at the corners the first time the wall is washed down.
Division bars and trims dry-set with no sealant, so wash water runs behind the panels at every joint.
Cutouts around outlets and pipes left oversized and open, so the sealant can not bridge them and the seam stays wet.

Common questions

6 answers

What does this frp wall panels final checklist cover?: 13 items across 4 sections, covering bond and flatness, trims and joints sealed, penetrations, condition and handover. Each item spells out what the person walking the job is actually looking for, not just a box to tick.
Who should run this inspection?: The panel installer with the GC's superintendent, walking the finished walls before the space is put into service.
When in the schedule should this walk happen?: After panels, trims and sealant are complete, before the kitchen or wet area is put into service and cleaned down.
Why do these items ask for a photo?: 10 of the 13 items call for photo evidence, 12 photos in all. A checklist answer without the photo is a claim; the photo is what makes the record worth something in a dispute and lets a reviewer approve work without re-walking the job.
What most often fails a frp wall panels final inspection?: Adhesive coverage short of full contact, so panels bubble and lifting starts at the corners the first time the wall is washed down. Division bars and trims dry-set with no sealant, so wash water runs behind the panels at every joint. Cutouts around outlets and pipes left oversized and open, so the sealant can not bridge them and the seam stays wet.
Can I use this checklist in RTI?: Yes. Start a free RTI workspace, build this list as a checklist, and the Photo Gate holds the submit button until every mandatory item is answered and its photos are attached. Approved inspections roll into a branded turnover package with a tamper evident audit trail.

Related checklists

FRP wall panels Rough-inFRP wall panels rough-in inspection checklistSubstrate flat, sound, dry and clean so the FRP will bond, with penetrations located before panels go up13 items10 photos FRP wall panels PunchFRP wall panels punch checklistCloseout callbacks for lifting edges, open sealant joints and gouged panels on the finished wet-area surface9 items3 photos

Run it with the Photo Gate

A checklist nobody can submit half-finished

Load this list into RTI, stick a QR tag on the area it covers, and the submit button stays locked until every mandatory item is answered and the 12 required photos exist. Approved walks roll into a branded turnover package with a tamper evident record behind every line.